C905_disassembly.pdf

SE C905 - instrukcja rozbiórki / wymiany obudowy

Instrukcja demontażu :)


Working Instruction, Mechanical

Working Instruction, Mechanical
Applicable for C905

CONTENTS

1 Introduction .............................................................................. 4
1.1 Equipment.................................................................................5
1.2 General cautions ......................................................................6
1.3 Adhesives .................................................................................6

2 Disassembly ............................................................................. 7
2.1
2.2
2.3
2.4
2.5

Overview ...................................................................................8
Battery Cover & Battery...........................................................9
Foil Flip Inner..........................................................................10
Keyboard.................................................................................10
Cap Plastic RF Numeric Keyboard & Cap Numeric
Keyboard.................................................................................11
2.6 Cover Flip Front......................................................................12
2.7 Display 2.41 TFT .....................................................................13
2.8 LCD Support Sheet ................................................................13
2.9 PBA Key Flex Flip Complete .................................................14
2.10 Cover Rear Assembly ............................................................16
2.11 Cover Base Rear Assembly...................................................17
2.12 Main PBA.................................................................................18
2.13 Loudspeaker Assembly .........................................................20
2.14 Flash Complete and Camera 8MP.........................................21

3 Replacements......................................................................... 23
3.1 Battery Cover & Battery.........................................................24
3.2 Cover Flip Front Assembly....................................................24
3.3 Cover Base Rear Assembly...................................................24
3.4 Flash Complete.......................................................................24
3.5 PBA Key Flex Flip Complete .................................................24
3.6 Slider FPC Assy......................................................................24
3.7 Cover Rear Assembly ............................................................24
3.8 Carrier Base Assembly ..........................................................25
3.9 Camera 8 MP...........................................................................25
3.10 Foil Flip Inner..........................................................................25
3.11 LCD Support Sheet ................................................................25
3.12 Loudspeaker Assembly .........................................................25
3.13 Screw 4.0x1.4..........................................................................25
3.14 Screw 2.3x1.4..........................................................................25
1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

1(87)

Working Instruction, Mechanical

3.15 Screw Torx 5.3x1.6 .................................................................26
3.16 Screw Torx 5.0x1.6 .................................................................26
3.17 Screw Philips M1.4x1.7 ..........................................................26
3.18 Cap Plastic RF Keyboard Numeric .......................................26
3.19 Cap Numeric Keyboard..........................................................26
3.20 Foil Adhesive Single Side 0.15 mm Flip Tape .....................26
3.21 Display 2.41 TFT .....................................................................27
3.22 Cover Flip Inner Metal............................................................27
3.23 Cap Reinforcement Plug (Right and Left) ............................28
3.24 Numeric Key Foil ....................................................................29
3.25 Keyboard Navigation .............................................................31
3.26 Key A/B Left ............................................................................32
3.27 Key A/B Right .........................................................................33
3.28 Co Brand Label.......................................................................34
3.29 Key Volume.............................................................................35
3.30 Key Mode ................................................................................35
3.31 Key Camera.............................................................................36
3.32 M2 Lid 37
3.33 Microphone Gasket ................................................................38
3.34 BT/WLAN Antenna .................................................................39
3.35 Left Sidepanel.........................................................................40
3.36 Right Sidepanel Bottom.........................................................41
3.37 Right Sidepanel Top...............................................................42
3.38 Ear Speaker.............................................................................43
3.39 Vibrator....................................................................................44
3.40 Light GU Navigation...............................................................45
3.41 Dome Foil Flip.........................................................................46
3.42 PBA Key Flex Flip Complete .................................................48
3.43 Shield Can Lid Flip .................................................................49
3.44 Cushion 1,0mm1,3x5,1,0 Conductive ...................................50
3.45 Foil Adhesive 0.048 mm Flex Flip .........................................51
3.46 Foil Adhesive Conductive 0.05 mm protection tape, front.52
3.47 Foil Adh Conduct GPS ESD protection tape .......................53
3.48 Foil Adhesive Double Side GPS Shieldcan .........................54
3.49 Foil Adhesive Double Side A/B Flex Tape ...........................55
3.50 Foil Adhesive Double Side GPS Antenna ............................56
3.51 Shield can lid, Vera ................................................................56
3.52 Shield can lid, regulator.........................................................57
3.53 Shield can lid, Kajsa...............................................................57
3.54 Shield can lid, WLAN .............................................................58
3.55 Shield Can Lid, Camera .........................................................58
3.56 Liquid Intrusion Indicator (1 and 2) ......................................59
3.57 Foil Adhesive LCD Support, left ...........................................61
3.58 Foil Adhesive LCD Support, right.........................................62
3.59 Light Gu Numeric ...................................................................63
3.60 Hinge Slide Mechanism .........................................................65
1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

2(87)

Working Instruction, Mechanical

3.61 Label 67

4 Reassembly ............................................................................ 68
4.1 Overview .................................................................................69
4.2 Flash Complete and Camera 8 MP........................................70
4.3 Loudspeaker Assembly .........................................................72
4.4 Main PBA.................................................................................72
4.5 Cover Base Rear Assembly...................................................76
4.6 Cover Rear Assembly ............................................................77
4.7 PBA Key Flex Flip Complete .................................................77
4.8 LCD Support Sheet ................................................................80
4.9 Display 2.41 TFT .....................................................................81
4.10 Cover Flip Front......................................................................82
4.11 Cap Plastic RF Numeric Keyboard & Cap Numeric
Keyboard.................................................................................83
4.12 Keyboard.................................................................................84
4.13 Foil Flip Inner..........................................................................85
4.14 Battery Cover & Battery.........................................................85

5 Country of Origin Barcodes for Brazil/VIVO Labels............ 86
6 Revision history ..................................................................... 87

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

3(87)

Working Instruction, Mechanical

1 Introduction

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

4(87)

Working Instruction, Mechanical

1.1 Equipment
SPECIAL TOOLS
Special tools text:
o NTZ122459
o NTZ122288
o NTZ112478
o NTZ1121052
o NTZ112302/2
o NTZ112521
o NTZ112590

Torque Screwdriver (or equivalent)
Bit (T6)
Bit (T5)
Bit(JCIS No 0)
Front opening tool
Flex film assembly tool
Plectrum/SVC & Repair

STANDARD TOOLS
Standard tools text:
o Dentist hook
o ESD tweezers
o Nylon Pointer
o Screwdriver

ESD EQUIPMENT
Protect the phone from ESD damages whenever it has
been opened by using:
o ESD-wristband
o ESD-gloves

LABEL EQUIPMENT
The following special equipment is required when replacing
or installing a new label:
o Hot air flow solder station
o Zebra printer connected to computer

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

5(87)

Working Instruction, Mechanical

1.2 General cautions
The following cautions are considered to be generic for all phone models and will not be repeated in
the Disassembly, Replacements and Reassembly sections:
o SWITCH OFF THE PHONE AND REMOVE ANY MEMORY STICK BEFORE THE START OF THE DISASSEMBLY!
o KEEP ALL CONTACT SURFACES CLEAN!
o BE CAREFUL WHEN USING TOOLS LIKE THE DENTIST HOOK, TWEEZERS, OPENING TOOLS, GUITAR PICK
ETC. TO AVOID SCRATCHES OR DAMAGES TO THE EXTERIOR AND INTERIOR PARTS OF THE PHONE!
o BE CAREFUL NOT TO DAMAGE ANY CONTACT SPRINGS!
o REMEMBER TO REMOVE THE PROTECTION FOILS ON NEW PARTS SUCH AS THE FRONT COVER AND LCD!
o NEVER TOUCH THE DISPLAY GLASS!
o USE AIR BLOW EQUIPMENT TO KEEP THE FRONT WINDOW AND DISPLAY MODULE DUST FREE!

1.3 Adhesives
Use a dentist hook and/or the tweezers to remove old adhesives.
Clean the surface with isopropyl alcohol before attaching new adhesives.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

6(87)

Working Instruction, Mechanical

2 Disassembly
When you are going to replace a part being listed in Replacements, the instruction of that section
usually begins by directing you to this Disassembly section with a specification of the instructions you
have to carry out in order to disassemble the phone as far as needed before returning to
Replacements for the actual replacement.

REPLACEMENTS
Start

Contents
page

DISASSEMBLY

REASSEMBLY
Done

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

7(87)

Working Instruction, Mechanical

2.1 Overview
The disassembly is done in the following sequence:
1. Battery Cover
1a. Battery
2. Flip Inner
3. Keyboard
4. Cap Plastic RF Numeric Keyboard & Cap Numeric
Keyboard
5. Cover Flip Front
6. Display 2.41 TFT
7. LCD Support Sheet
8. PBA Key Flex Flip Complete
9. Cover Rear Assembly
10. Cover Base Rear Assembly
11. Main PBA
12. Loudspeaker Assembly
13. Flash Complete and Camera 8MP
14. Carrier Base Assembly

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

8(87)

Working Instruction, Mechanical

2.2

Battery Cover & Battery

Remove the Battery Cover.

Remove the Battery.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

9(87)

Working Instruction, Mechanical

2.3 Foil Flip Inner

Use a pair of ESD tweezers to remove the Flip Inner.

Use a Screwdriver with JCIS Bit to remove the two Screws
4.0x1.4.

2.4 Keyboard

Use a Screwdriver to loosen the keyboard from the opposite
side

Use a Flex Film Assembly Tool to remove the Keyboard

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

10(87)

Working Instruction, Mechanical

2.5 Cap Plastic RF Numeric Keyboard & Cap Numeric
Keyboard

Use a Screwdriver to remove the Cap Plastic RF Keyboard
Numeric on the opposite side.

Use Screwdriver to remove the Cap Numeric keyboard on
the opposite side.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

11(87)

Working Instruction, Mechanical

2.6 Cover Flip Front

Use your fingers to slide and position the Cover Flip Front
to make the two Screws 2.3x1.4 visible through the two
holes in the Cover Base Rear Assembly.

Use a Screwdriver with JCIS Bit to remove the two Screws
2.3x1.4.

Use a Guitar Pick to loosen the Cover Flip Front on both
sides.

Use your fingers to remove the Cover Flip Front.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

12(87)

Working Instruction, Mechanical

2.7 Display 2.41 TFT

Locate the three snap hooks and use a Front Opening Tool
to release the PCB-part of the PBA Key Flex Flip Complete.

Use a Front Opening Tool to disconnect the LCD FPC
Connector
BE VERY CAREFUL WHEN BENDING THE PCB-PART OF THE
KEY FLEX FLIP
BE VERY CAREFUL NOT TO DAMAGE THE DISPLAY FLEX!

Use a Front Opening Tool to remove the Display 2.41 TFT.

2.8 LCD Support Sheet

Use a blunt pair of Tweezers to remove the LCD Support
Sheet.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

13(87)

Working Instruction, Mechanical

2.9 PBA Key Flex Flip Complete

Use a Flex Film Assembly Tool to remove the Foil Adhesive
Single Side 0.15 mm Flip Tape

Use a Front Opening Tool to unsnap the PBA Key Flex Flip
Complete connector

Use a Flex Film Assembly Tool to disconnect the Slider
FPC Assy from the PBA Key Flex Complete

Use a Front Opening Tool to loosen the GPS Antenna.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

14(87)

Working Instruction, Mechanical

Use a Front Opening Tool to loosen the Key B part of the
Board.

Use a Front Opening Tool to loosen the Key A part of the
Board.

Use a Front Opening Tool to loosen the GPS part of the
Board.

Use a Flex Film Assembly Tool to remove the PBA Key
Flex Flip Complete

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

15(87)

Working Instruction, Mechanical

2.10 Cover Rear Assembly

Use a Flex Film Assembly Tool to loosen the Slider PPC
Assy from the Cover Rear Assembly

Use a Screwdriver with JCIS Bit to remove the four Flat
Head M1.4x1.7

Use a Flex Film Assembly Tool to loosen the Slider PPC
Assy from the back of the Cover Rear Assembly

Use your fingers to remove the Cover Rear Assembly

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

16(87)

Working Instruction, Mechanical

2.11 Cover Base Rear Assembly

Use a Screwdriver with T5 Bit to remove the two Screws
Torx 5.0x1.6.

Use a Screwdriver with T6 Bit to remove the two Screws
Torx 5.3x1.6.

Use a Guitar Pick to loosen the Cover Base Rear Assembly
on three sides

Use your fingers to remove the Cover Base Rear Assembly.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

17(87)

Working Instruction, Mechanical

2.12 Main PBA

Use a Front Opening Tool to disconnect the Numeric Key
Foil Connector from the Main PBA

Use a Flex Film Assembly Tool to pull the Numeric Key Foil
out of the camera key switch supporter.

Use a Pair of ESD Tweezers to loosen the BT/WLAN
Antenna

BE VERY CAREFUL NOT TO DAMAGE THE MAIN PBA SWITCHES
WHEN LOOSENING THE MAIN PBA!
Use a Front Opening Tool to bend the Carrier Base
Assembly away from the Main PBA and loosen the Main
PBA.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

18(87)

Working Instruction, Mechanical

Use a Front Opening Tool to bend the Carrier Base
Assembly away from the Main PBA and loosen the Main
PBA.

BE VERY CAREFUL NOT TO DAMAGE THE MAIN PBA SWITCHES
WHEN REMOVING THE MAIN PBA!
Use a Front Opening Tool to bend the Carrier Base
Assembly away from the Main PBA and loosen the Main
PBA.

BE VERY CAREFUL NOT TO DAMAGE THE SLIDER FPC ASSY!
Use your fingers to gently thread the Slider FPC Assy
through the gap

Use A Flex Film Assembly Tool to Loosen the Slider FPC
Assy Adhesive from the 100 pin FPC connector
BE VERY CAREFUL NOT TO DAMAGE THE SLIDER FPC ASSY!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

19(87)

Working Instruction, Mechanical

Use a Front Opening Tool to unhook the board to flex
connector from the Main PBA.

Use a Flex Film Assembly Tool to remove the Slider FPC
Assy from the Main PBA
BE VERY CAREFUL NOT TO DAMAGE THE SLIDER FPC ASSY!

2.13 Loudspeaker Assembly

Use a Front Opening Tool to release the snap hooks and
remove the Loudspeaker Assembly.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

20(87)

Working Instruction, Mechanical

2.14 Flash Complete and Camera 8MP

Use a Dentist Hook to remove the Shield Can Lid, Camera

Use a Front Opening Tool to disconnect the Camera
Connector from the Main PBA

Use a Front Opening Tool to release the five snap hooks

Turn over the Main PBA and use a Front Opening Tool to
disconnect the Flash Complete from the Main PBA

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

21(87)

Working Instruction, Mechanical

Use your fingers to gently remove the Camera 8MP from
the Flash Complete

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

22(87)

Working Instruction, Mechanical

3 Replacements
Search for the part to be replaced on the Contents page and go to that instruction to be found in this
Replacements section.
The instruction usually begins by directing you to the Disassembly section with a specification of the
instructions you have to carry out in order to disassemble the phone as far as needed before the
actual replacement.
Go back to this Replacements section and carry out the instruction.
The instruction usually ends by directing you to the Reassembly section with a specification of the
instructions you have to carry out in order to reassemble the phone.

REPLACEMENTS
Start

Contents
page

DISASSEMBLY

REASSEMBLY
Done

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

23(87)

Working Instruction, Mechanical

3.1 Battery Cover & Battery
Follow the 2.2 Disassembly instructions!
Replace Battery Cover and/or Battery
Follow the 4.14 Reassembly instructions!

3.2 Cover Flip Front Assembly
Follow the 2.2 - 2.6 Disassembly instructions!
Replace Cover Flip Front Assembly
Follow the 4.10 - 4.14 Reassembly instructions!

3.3 Cover Base Rear Assembly
Follow the 2.2 - 2.11 Disassembly instructions!
Replace Cover Base Rear Assembly
Follow the 4.5 - 4.14 Reassembly instructions!

3.4 Flash Complete
Follow the 2.2 - 2.14 Disassembly instructions!
Replace Flash Complete
Follow the 4.2 - 4.14 Reassembly instructions!

3.5 PBA Key Flex Flip Complete
Follow the 2.2 - 2.9 Disassembly instructions!
Replace Key Flex Flip Complete
Follow the 4.7 - 4.14 Reassembly instructions!!

3.6 Slider FPC Assy
Follow the 2.2 - 2.12 Disassembly instructions!
Replace Slider FPC Assy
Follow the 4.4 - 4.14 Reassembly instructions!

3.7

Cover Rear Assembly

Follow the 2.2 - 2.10 Disassembly instructions!
Replace Cover Rear Assembly
Follow the 4.6 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

24(87)

Working Instruction, Mechanical

3.8 Carrier Base Assembly
Follow the 2.2 - 2.12 Disassembly instructions! And 3.29-3.31, 3.34 - 3.36, 3.62 Replacement
Instructions!
Replace Carrier Base Assembly
Follow the 4.4 - 4.14 Reassembly instructions! And 3.29-3.31, 3.34 - 3.36, 3.62 Replacement
Instructions!

3.9 Camera 8 MP
Follow the 2.2 - 2.14 Disassembly instructions!
Replace Camera 8 MP
Follow the 4.2 - 4.14 Reassembly instructions!

3.10 Foil Flip Inner
Follow the 2.2 - 2.3 Disassembly instructions!
Replace Foil Flip Inner
Follow the 4.13 - 4.14 Reassembly instructions!

3.11 LCD Support Sheet
Follow the 2.2 - 2.8 Disassembly instructions!
Replace LCD Support Sheet
Follow the 4.8 - 4.14 Reassembly instructions!

3.12 Loudspeaker Assembly
Follow the 2.2 - 2.13 Disassembly instructions!
Replace Loudspeaker Assembly
Follow the 4.3 - 4.14 Reassembly instructions!

3.13 Screw 4.0x1.4
Follow the 2.2 - 2.3 Disassembly instructions!
Replace Screw 4.0x1.4 (torque 11Ncm)
Follow the 4.13 - 4.14 Reassembly instructions!

3.14 Screw 2.3x1.4
Follow the 2.2 - 2.6 Disassembly instructions!
Replace Screw 2.3x1.4 (torque 11Ncm)
Follow the 4.10 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

25(87)

Working Instruction, Mechanical

3.15 Screw Torx 5.3x1.6
Follow the 2.2 - 2.11 Disassembly instructions!
Replace Screw Torx 5.3x1.6 (torque 11Ncm)
Follow the 4.5 - 4.14 Reassembly instructions!

3.16 Screw Torx 5.0x1.6
Follow the 2.2 - 2.11 Disassembly instructions!
Replace Screw Torx 5.0x1.6 (torque 11Ncm)
Follow the 4.5 - 4.14 Reassembly instructions!

3.17 Screw Philips M1.4x1.7
Follow the 2.2 - 2.12 Disassembly instructions! And 3.62 Replacement Instructions!
Replace Flat Head M1.4x1.7 (torque 11Ncm)
Follow the 4.4 - 4.14 Reassembly instructions! And 3.62 Replacement Instructions!

3.18 Cap Plastic RF Keyboard Numeric
Follow the 2.2 - 2.5 Disassembly instructions!
Replace Cap Plastic RF Numeric Keyboard
Follow the 4.11 - 4.14 Reassembly instructions!

3.19 Cap Numeric Keyboard
Follow the 2.2 - 2.5 Disassembly instructions!
Replace Cap Numeric Keyboard
Follow the 4.11 - 4.14 Reassembly instructions!

3.20 Foil Adhesive Single Side 0.15 mm Flip Tape
Follow the 2.2 - 2.9 Disassembly instructions!
Replace Foil Adhesive Single Side 0.15 mm Flip Tape
Follow the 4.7 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

26(87)

Working Instruction, Mechanical

3.21 Display 2.41 TFT
Follow the 2.2 - 2.7 Disassembly instructions!
Fold the Display Flex between the cutouts.
Replace Display 2.41 TFT
Follow the 4.9 - 4.14 Reassembly instructions!

3.22 Cover Flip Inner Metal
Removal
Follow the 2.3 Disassembly instructions!
Use a Guitar Pick to loosen the Cover Flip Inner Metal. Use
your fingers to remove the Cover Flip Inner Metal.

Installation
Use your fingers to place the Cover Flip Inner Metal.

Use your fingers to attach the Cover Flip Inner Metal. Press
with your fingers on the entire surface
Follow the 4.13 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

27(87)

Working Instruction, Mechanical

3.23 Cap Reinforcement Plug (Right and Left)
Removal (Right)
Follow the 22 - 2.9 Disassembly instructions!
Use a dentist hook to remove the Cap Reinforcement Plug
Right.

Installation
Use a pair of ESD Tweezers to attach the Cap
Reinforcement Plug (Right)
Follow the 4.7 - 4.14 Reassembly instructions!

Removal (Left)
Follow the 2.2 - 2.9 Disassembly instructions!
Use a dentist hook to remove the Cap Reinforcement Plug
Left.

Installation
Use a pair of ESD Tweezers to attach the Cap
Reinforcement Plug (Right)
Follow the 4.7 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

28(87)

Working Instruction, Mechanical

3.24 Numeric Key Foil
Removal
Follow the 2.2 - 2.12 Disassembly instructions!
Use a blunt pair of Tweezers to remove the Light GU
Numeric.

Use a Flex Film Assembly Tool to remove the Numeric Key
Foil.

Installation
Use your fingers to position the Numeric Key Foil.

MAKE SURE THE ALIGNMENT IS CORRECT!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

29(87)

Working Instruction, Mechanical

Use your fingers to attach the Numeric Key Foil

Use a pair of ESD Tweezers to position the Light GU
Numeric

MAKE SURE THE ALIGNMENT IS CORRECT!

Use your fingers to attach the Light Gu Numeric
Follow the 4.4 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

30(87)

Working Instruction, Mechanical

3.25 Keyboard Navigation

Removal
Follow the 2.2 - 2.6 Disassembly instructions!
Use a pair of ESD Tweezers to loosen the Keyboard
Navigation from the Cover Flip Front.

Use a pair of ESD Tweezers to remove the Keyboard
Navigation from the Cover Flip Front.

Installation
Use your fingers to position the center of the Keyboard
Navigation on the Cover Flip Front.
BE CAREFUL NOT TO TOUCH THE ADHESIVE!

Use your fingers to attach the Keyboard Navigation.
Follow the 4.10 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

31(87)

Working Instruction, Mechanical

3.26 Key A/B Left

Removal
Follow the 2.2 - 2.6 Disassembly instructions!
Use a pair of ESD Tweezers to remove the Key A/B Left
from the Cover Flip Front.

Installation
Use your fingers to attach the Key A/B Left on the Cover
Flip Front.
Follow the 4.10 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

32(87)

Working Instruction, Mechanical

3.27 Key A/B Right
Removal
Follow the 2.2 - 2.6 Disassembly instructions!
Use a pair of ESD Tweezers to remove the Key A/B Right
from the Cover Flip Front.

Installation
Use your fingers to attach the Key A/B Right on the Cover
Flip Front.
Follow the 4.10 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

33(87)

Working Instruction, Mechanical

3.28 Co Brand Label
Removal
BE CAREFUL NOT TO DAMAGE THE COVER FLIP FRONT!

No disassembly needed!
Use a Dentist Hook to loosen the Co Brand Label.

Use a pair of ESD Tweezers to remove the Co Brand Label.

Installation
Use a pair of ESD Tweezers to place the Co Brand Label.

Use your fingers to attach the Co Brand Label.
No reassembly needed!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

34(87)

Working Instruction, Mechanical

3.29 Key Volume
Removal
Follow the 2.2 - 2.12 Disassembly instructions!
Use a pair of ESD Tweezers to remove the Key Volume.

Installation
Use a pair of ESD Tweezers to position the Key Volume.
Follow the 4.4 - 4.14 Reassembly instructions!

3.30 Key Mode
Removal
Follow the 2.2 - 2.12 Disassembly instructions!
Use a pair of ESD Tweezers to remove the Key Mode.

Installation
Use a pair of ESD Tweezers to position the Key Mode.
Follow the 4.4 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

35(87)

Working Instruction, Mechanical

3.31 Key Camera

Removal
Follow the 2.2 - 2.12 Disassembly instructions!
Use a pair of ESD Tweezers to remove the Key Camera.

Installation
Use a pair of ESD Tweezers to position the Key Camera.
Follow the 4.4 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

36(87)

Working Instruction, Mechanical

3.32 M2 Lid

Removal
Follow the 2.2 - 2.11 Disassembly instructions!
Open the M2 Lid.

Use a pair of ESD Tweezers to remove the M2 Lid.

Installation
Use your fingers to position the M2 Lid.
Follow the 4.5 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

37(87)

Working Instruction, Mechanical

3.33 Microphone Gasket
Removal
Follow the 2.2 - 2.6 Disassembly instructions!
Use a pair of ESD Tweezers to remove the Microphone
Gasket.

Installation
Use a pair of ESD Tweezers to position the Microphone
Gasket.
Follow the 4.10 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

38(87)

Working Instruction, Mechanical

3.34 BT/WLAN Antenna
Removal
Follow the 2.2 - 2.12 Disassembly instructions!
Use a Front Opening Tool to loosen the BT/WLAN Antenna.

Use a Front Opening Tool to disconnect the BT/WLAN
Antenna.

Installation
Use your fingers to connect the BT/WLAN Antenna.
MAKE SURE THE BT/WLAN ANTENNA IS COMPLETELY
CONNECTED!

Use a Front Opening Tool to attach the BT/WLAN Antenna
MAKE SURE THE BT/WLAN ANTENNA IS COMPLETELY HELD
BY THE CLIP!
Follow the 4.4- 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

39(87)

Working Instruction, Mechanical

3.35 Left Sidepanel
Removal
No Disassembly needed!
Use a Dentist Hook to remove the Left Sidepanel.

Installation
Use a Flex Film Assembly Tool to position the Left
Sidepanel.

Use your fingers to attach the Left Sidepanel
No Reassembly needed!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

40(87)

Working Instruction, Mechanical

3.36 Right Sidepanel Bottom

Removal
No Disassembly needed!
Use a Dentist Hook to remove the Right Sidepanel Bottom.

Installation
Use a Flex Film Assembly Tool to position the Right
Sidepanel Bottom.

Use your fingers to attach the Right Sidepanel Bottom
No Reassembly needed!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

41(87)

Working Instruction, Mechanical

3.37 Right Sidepanel Top
Removal
No Disassembly needed!
Use a Dentist Hook to loosen the Right Sidepanel Top

Use a Flex Film Assembly Tool to remove the Right
Sidepanel Top

Installation
Use a Flex Film Assembly Tool to position the Right
Sidepanel Top

Use your fingers to attach the Right Sidepanel Top
No Reassembly needed!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

42(87)

Working Instruction, Mechanical

3.38 Ear Speaker
Removal
Follow the 2.2 - 2.6 Disassembly instructions!
Use a Dentist Hook to loosen the Ear Speaker.

Use a pair of ESD Tweezers to remove the Ear Speaker.

Installation
Use a pair of ESD Tweezers to place the Ear Speaker.
MAKE SURE TO ALIGN THE SPEAKER PROPERLY! SEE ARROW!

MAKE SURE TO ALIGN THE SPEAKER PROPERLY!
DO NOT TOUCH THE SPRINGS ON THE EAR SPEAKER!
Follow the 4.10 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

43(87)

Working Instruction, Mechanical

3.39 Vibrator
Removal
Follow the 2.2 - 2.14 Disassembly instructions!
Use a Front Opening Tool to remove Vibrator.

Installation
Use a pair of ESD Tweezers to position the Vibrator.

Use a Front Opening Tool to attach the Vibrator.
DO NOT TOUCH THE SPRINGS ON THE VIBRATOR!
Follow the 4.2 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

44(87)

Working Instruction, Mechanical

3.40 Light GU Navigation
Removal
Follow the 2.2 - 2.6 Disassembly instructions!
Use a Flex Film Assembly Tool to remove the Light GU
Navigation

Installation
Use a Flex Film Assembly Tool to position the Light GU
Navigation

MAKE SURE THE ALIGNMENT IS CORRECT!

Use your fingers to attach the Light Gu Navigation
DO NOT ATTACH THE LIGHT GU NAVIGATION BY PRESSING ON
THE BUTTONS!
Follow the 4.10 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

45(87)

Working Instruction, Mechanical

3.41 Dome Foil Flip
Removal
Follow the 2.2 - 2.6 Disassembly instructions!
Use a Flex Film Assembly Tool to remove the Light GU
Navigation

Use a Flex Film Assembly Tool to remove the Dome Foil
Flip

Installation
Use a Flex Film Assembly Tool to position the Dome Foil
Flip

MAKE SURE THE ALIGNMENT IS CORRECT!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

46(87)

Working Instruction, Mechanical

Use your fingers to attach the Dome Foil Flip
DO NOT ATTACH THE LIGHT GU NAVIGATION BY PRESSING ON
THE BUTTONS!

Use a Flex Film Assembly Tool to position the Light GU
Navigation

MAKE SURE THE ALIGNMENT IS CORRECT!

Use your fingers to attach the Light Gu Navigation
DO NOT ATTACH THE LIGHT GU NAVIGATION BY PRESSING ON
THE BUTTONS!
Follow the 4.10 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

47(87)

Working Instruction, Mechanical

3.42 PBA Key Flex Flip Complete

Removal
Follow the 2.2 - 2.9 Disassembly instructions!

Installation
Follow the 4.7 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

48(87)

Working Instruction, Mechanical

3.43 Shield Can Lid Flip
Removal
Follow the 2.2 - 2.9 Disassembly instructions!
Use a Dentist Hook to loosen the Shield Can Lid Flip

Use a Flex Film Assembly Tool to remove the Shield Can
Lid Flip

Installation
Use a Flex Film Assembly Tool to position the Shield Can
Lid Flip

Use your fingers to attach the Shield Can Lid Flip
Follow the 4.7 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

49(87)

Working Instruction, Mechanical

3.44 Cushion 1,0mm1,3x5,1,0 Conductive
Removal
Follow the 2.2 - 2.6 Disassembly instructions!
Use a Pair of ESD Tweezers to remove the Cushion
1,0mm1,3x5,1,0 Conductive

Installation
Use a Pair of ESD Tweezers to attach the Cushion
1,0mm1,3x5,1,0 Conductive
MAKE SURE THE ALIGNMENT IS CORRECT!
Follow the 4.10 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

50(87)

Working Instruction, Mechanical

3.45 Foil Adhesive 0.048 mm Flex Flip
Removal
Follow the 2.2 - 2.9 Disassembly instructions!
Use a Guitar Pick to peel off the Foil Adhesive 0.048 mm
Flex Flip

Use a Guitar Pick to peel off the Foil Adhesive 0.048 mm
Flex Flip from the PBA Key Flex Flip Complete

Installation

Use a Flex Film Assembly Tool to position the Foil Adhesive
0.048 mm Flex Flip on the PBA Key Flex Flip Complete

Use a Flex Film Assembly Tool to remove the protection
tape from the Foil Adhesive 0.048 mm Flex Flip
Follow the 4.7 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

51(87)

Working Instruction, Mechanical

3.46 Foil Adhesive Conductive 0.05 mm protection
tape, front
Removal
Follow the 2.2 - 2.6 Disassembly instructions!
Use a pair of ESD Tweezers to remove the Foil Adhesive
Conductive 0.05 mm protection tape, front

Installation
Use a Flex Film Assembly Tool to position the Foil Adhesive
Conductive 0.05 mm protection tape, front

Use a Flex Film Assembly Tool to remove the protection
tape from the Foil Adhesive Conductive 0.05 mm protection
tape, front
MAKE SURE THE FOIL ADHESIVE CONDUCTIVE 0.05 MM GPS
ESD PROTECTION TAPE, FRONT COMPLETELY COVER THE
COVER FLIP FRONT!
Follow the 4.10 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

52(87)

Working Instruction, Mechanical

3.47 Foil Adh Conduct GPS ESD protection tape
Removal
Follow the 2.2 - 2.9 Disassembly instructions!
Use a Dentist Hook to remove the Foil Adh Conduct GPS
ESD protection tape

Installation
Use a Flex Film Assembly Tool to position the Foil Adh
Conduct GPS ESD protection tape

Use a Flex Film Assembly Tool to attach the Foil Adh
Conduct GPS ESD protection tape
Follow the 4.7 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

53(87)

Working Instruction, Mechanical

3.48 Foil Adhesive Double Side GPS Shieldcan
Removal
Follow the 2.2 - 2.9 Disassembly instructions!
Use a Dentist Hook to remove the Foil Adhesive Conductive
GPS ESD protection tape,

Use a Dentist Hook to remove the Foil Adhesive Double
Side GPS Shieldcan

Installation
Use a Flex Film Assembly Tool to position the Foil Adhesive
Double Side GPS Shieldcan

Use a Flex Film Assembly Tool to position the Foil Adhesive
Conductive GPS ESD protection tape

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

54(87)

Working Instruction, Mechanical

Use a Flex Film Assembly Tool to attach the Foil Adhesive
Conductive GPS ESD protection tape
Follow the 4.7 - 4.14 Reassembly instructions!

3.49 Foil Adhesive Double Side A/B Flex Tape
Removal
Follow the 2.2 - 2.9 Disassembly instructions!
Use a Dentist Hook remove the two Foil Adhesive Double
Side A/B Flex Tape

Installation
Use a pair of ESD Tweezers to attach the two Foil Adhesive
Double Side A/B Flex Tape
Follow the 4.7 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

55(87)

Working Instruction, Mechanical

3.50 Foil Adhesive Double Side GPS Antenna
Removal
Follow the 2.2 - 2.9 Disassembly instructions!
Use a Dentist Hook remove the Foil Adhesive Double Side
GPS Antenna

Installation
Use a Flex Film Assembly Tool to position and attach the
Foil Adhesive Double Side GPS Antenna. Remove the
Protection tape from the Foil Adhesive Double Side GPS
Antenna
Follow the 4.7 - 4.14 Reassembly instructions!

3.51 Shield can lid, Vera
Removal
Follow the 2.2 - 2.13 Disassembly instructions!
Use a Dentist Hook to remove the Shield Can Lid, Vera

Installation
Use your fingers to attach the Shield Can Lid, Vera
Follow the 4.3 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

56(87)

Working Instruction, Mechanical

3.52 Shield can lid, regulator
Removal
Follow the 2.2 - 2.14 Disassembly instructions!
Use a Dentist Hook to remove the Shield Can Lid, regulator

Installation
Use your fingers to attach the Shield Can Lid, regulator
Follow the 4.2 - 4.14 Reassembly instructions!

3.53 Shield can lid, Kajsa
Removal
Follow the 2.2 - 2.13 Disassembly instructions!
Use a Dentist Hook to remove the Shield Can Lid, Kajsa

Installation
Use your fingers to attach the Shield Can Lid, Kajsa
Follow the 4.3 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

57(87)

Working Instruction, Mechanical

3.54 Shield can lid, WLAN
Removal
Follow the 2.2 - 2.14 Disassembly instructions!
Use a Dentist Hook to remove the Shield Can Lid, WLAN

Installation
Use your fingers to attach the Shield Can Lid, WLAN
Follow the 4.2 - 4.14 Reassembly instructions!

3.55 Shield Can Lid, Camera
Removal
Follow the 2.2 - 2.12 Disassembly instructions!
Use a Dentist Hook to remove the Shield Can Lid, Camera

Installation
Use your fingers to attach the Shield Can Lid, Camera
Follow the 4.4 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

58(87)

Working Instruction, Mechanical

3.56 Liquid Intrusion Indicator (1 and 2)
Removal (1)
Follow the 2.2 - 2.11 Disassembly instructions!
Use a Dentist Hook to remove the Liquid Intrusion Indicator

Installation (1)
Use a Flex Film Assembly Tool to attach the Liquid
Intrusion Indicator
Follow the 4.5 - 4.14 Reassembly instructions!

Removal (2)
Follow the 2.2 - 2.6 Disassembly instructions!
Use a Dentist Hook to remove the Liquid Intrusion Indicator

Installation (2)
MAKE SURE THE LIQUID INTRUSION INDICATOR IS WITHIN THE
LINES!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

59(87)

Working Instruction, Mechanical

Use a Flex Film Assembly Tool to attach the Liquid
Intrusion Indicator
Follow the 4.10 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

60(87)

Working Instruction, Mechanical

3.57 Foil Adhesive LCD Support, left
Removal
Follow the 2.2 - 2.8 Disassembly instructions!
Use a Dentist Hook to loosen the Foil Adhesive LCD
Support, left

Use a Flex Film Assembly Tool to remove the Foil Adhesive
LCD Support, left

Installation
Use a Flex Film Assembly Tool to position the Foil Adhesive
LCD Support, left

Use a your fingers to attach the Foil Adhesive LCD Support,
left
Follow the 4.8 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

61(87)

Working Instruction, Mechanical

3.58 Foil Adhesive LCD Support, right
Removal
Follow the 2.2 - 2.8 Disassembly instructions!
Use a Dentist Hook to loosen the Foil Adhesive LCD
Support, right

Use a Flex Film Assembly Tool to remove the Foil Adhesive
LCD Support, right

Installation
Use a Flex Film Assembly Tool to position the Foil Adhesive
LCD Support, right

Use a your fingers to attach the Foil Adhesive LCD Support,
right
Follow the 4.8 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

62(87)

Working Instruction, Mechanical

3.59 Light GU Numeric
Removal
Follow the 2.2, 2.4 - 2.5 Disassembly instructions!
Use a pair of ESD Tweezers to loosen the Light GU
Numeric

Use a pair of ESD Tweezers to remove the Light GU
Numeric

Installation
Use a pair of ESD Tweezers to position the Light GU
Numeric

MAKE SURE THE ALIGNMENT IS CORRECT!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

63(87)

Working Instruction, Mechanical

Use your fingers to attach the Light GU Numeric
Follow the 4.11 - 4.12, 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

64(87)

Working Instruction, Mechanical

3.60 Hinge Slide Mechanism
Removal
Follow the 2.2 - 2.12 Disassembly instructions!
Use a Screwdriver with JCIS Bit to remove the four Flat
Head M1.4x1.7.

Use a Screwdriver with JCIS Bit to remove the two Flat
Head M1.4x1.7.

Turn over the phone and use your fingers to remove the
Hinge Mechanism.

Installation
Use your fingers to position the Hinge Mechanism

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

65(87)

Working Instruction, Mechanical

Turn over the phone and use a Screwdriver with JCIS Bit
(torque 11Ncm) to insert and tighten the two Flat Head
M1.4x1.7.

Use a Screwdriver with JCIS Bit (torque 11Ncm) to insert
and tighten the four Flat Head M1.4x1.7.
Follow the 4.4 - 4.14 Reassembly instructions!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

66(87)

Working Instruction, Mechanical

3.61 Label
Follow the 2.2 Disassembly instructions!

o Read the old label and/or write the information into
the "Label make" program before removal
Note the position of the label before removal
Heat up the label by using hot air, if needed
Carefully remove the label without causing
scratches
If there still are residues, clean the surface with
isopropyl alcohol

o NOTE: IF YOU ARE PRINTING A BRAZIL OR VIVO
LABEL, REFER TO SECTION 5 FOR MORE
INFORMATION ON THE COUNTRY OF
ORIGIN.

Check that the proper label format is loaded in the
Zebra printer
Write a new label by using the program "Label
make" and check that the printing is OK
Take the new label and place it onto the frame as
in the adjacent picture
NOTE: DO NOT GET ANY LABEL ADHESIVE ON THE
BATTERY
CONTACTS.
ONE LABEL ONLY IS ALLOWED!

Follow the 4.14 Reassembly instructions

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

67(87)

Working Instruction, Mechanical

4 Reassembly
After replacing a part being listed in Replacements, the instruction of that section usually ends by
directing you to this Reassembly section with a specification of the instructions you have to carry out
in order to reassemble the phone.

REPLACEMENTS
Start

Contents
page

DISASSEMBLY

REASSEMBLY
Done

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

68(87)

Working Instruction, Mechanical

4.1 Overview
The reassembly is done in the following sequence:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

Carrier Base Assembly
Flash Complete and Camera 8MP
Loudspeaker Assembly
Main PBA
Cover Base Rear Assembly
Cover Rear Assembly
PBA Key Flex Flip Complete
LCD Support Sheet
Display 2.41 TFT
Cover Flip Front
Cap Plastic RF Numeric Keyboard &
Cap Numeric Keyboard
12. Keyboard
13. Flip Inner
14. Battery
14a. Battery Cover

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

69(87)

Working Instruction, Mechanical

4.2 Flash Complete and Camera 8 MP

Use your fingers to attach the connector
ENSURE THAT THERE IS A GOOD CONNECTION!

Use your fingers to turn over the Flash Complete.

Locate the five snap hooks and use your fingers to snap on
the Flash Complete.

Use your fingers to position the Camera 8MP
DO NOT INSERT THE CAMERA TO DEEP!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

70(87)

Working Instruction, Mechanical

MAKE SURE THE ALIGNMENT IS CORRECT!

Use your fingers to attach the connector
ENSURE THAT THERE IS A GOOD CONNECTION!
DO NOT BEND THE FLEX BEFORE THE CONNECTOR IS
ATTACHED!
BEND THE FLEX AS THE PICTURE SHOWS!

Use your fingers to attach the Shield Can Lid, Camera

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

71(87)

Working Instruction, Mechanical

4.3 Loudspeaker Assembly

Use your fingers to position the Loudspeaker Assembly.

Use your fingers to snap on the Loudspeaker Assembly.

4.4 Main PBA

Use a Flex Film Assembly Tool to attach the Slider FPC
Assy to the main PBA connector
ENSURE THAT THERE IS A GOOD CONNECTION!

Use a Front Opening Tool to close the connectors lock

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

72(87)

Working Instruction, Mechanical

Fold the Slider FPC Assy along the white line.
(Slider FPC Assy not mounted for visibility)

Attach the Slider FPC Assy to the Main PBA..

The white line shall not be visible when looking from above

Use your fingers to thread the Slider FPC Assy through the
gap
BE VERY CAREFUL NOT TO DAMAGE THE SLIDER FPC ASSY!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

73(87)

Working Instruction, Mechanical

Use your fingers to position the Main PBA
MAKE SURE THE NUMERIC KEY FOIL IS POSITIONED
CORRECTLY WHEN POSITIONING THE MAIN PBA!

Use a Front Opening Tool and your fingers to position the
Main PBA.
BE VERY CAREFUL NOT TO DAMAGE THE MAIN PBA SWITCHES
BY USING A FRONT OPENING TOOL AND BENDING OUT THE
CARRIER BASE ASSY!

Use a Flex Film Assembly Tool to attach the connector to
the Main PBA
ENSURE THAT THERE IS A GOOD CONNECTION!

Use a Flex Film Assembly Tool to position the Key Camera
Flex in the camera key switch supporter

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

74(87)

Working Instruction, Mechanical

Use a Flex Film Assembly Tool to position and attach the
BT/WLAN Antenna
MAKE SURE THE BT/WLAN ANTENNA IS COMPLETELY HELD
BY THE CLIP!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

75(87)

Working Instruction, Mechanical

4.5 Cover Base Rear Assembly

Use your fingers to position the Cover Base Rear
Assembly.

Use your fingers to snap on the Cover Base Rear
Assembly.

Use a Screwdriver with T6 Bit to assemble the two Screws
Torx 5.3x1.6 (torque 11Ncm).

Use a Screwdriver with T5 Bit to assemble the two Screws
Torx 5.0x1.6 (torque 11Ncm).

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

76(87)

Working Instruction, Mechanical

4.6 Cover Rear Assembly

Use your fingers to position the Cover Rear Assembly

Use a Screwdriver with JCIS Bit (torque 11Ncm) to insert
and tighten the four Flat Head M1.4x1.7

4.7 PBA Key Flex Flip Complete

ENSURE THAT THERE IS A SPACER FOR RIGID FLEX
FIXATION MOUNTED!
Align the Spacer for Rigid Flex Fixation with the "golden"
line at the corner.

Use a Flex Film Assembly Tool to connect the PBA Key
Flex Flip Complete to the Slider FPC Assy
ENSURE THAT THERE IS A GOOD CONNECTION!

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

77(87)

Working Instruction, Mechanical

Use a Front Opening Tool to snap on the PBA Key Flex Flip
Complete to Slider FPC Assy

MAKE SURE TO ALIGN THE PBA KEY FLEX FLIP COMPLETE
PROPERLY TO THE COVER REAR ASSY!

Use your fingers to attach Key A and Key B
USE THE GUIDE PINS ON THE COVER REAR ASSY TO ALIGN
KEY A AND KEY B!

Use your fingers to attach the GPS Antenna

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

78(87)

Working Instruction, Mechanical

Use your fingers to attach the PBA Key Flex Flip Complete.

Use a Flex Film Assembly Tool to position the Foil Adhesive
Single Side 0.15 mm Flip Tape

MAKE SURE THE ALIGNMENT IS CORRECT!

Use your fingers to attach the Foil Adhesive Single Side
0.15 mm Flip Tape

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

79(87)

Working Instruction, Mechanical

4.8 LCD Support Sheet

Use a blunt pair of Tweezers and your fingers to attach the
LCD Support Sheet.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

80(87)

Working Instruction, Mechanical

4.9 Display 2.41 TFT

Use your fingers to position the Display 2.41 TFT.

Attach the connector to the PBA Key Flex Flip Complete
ENSURE THAT THERE IS A GOOD CONNECTION!

MAKE SURE THE PBA KEY FLEX FLIP COMPLETE IS
PROPERLY ALIGNED AS THE PICTURE SHOWS!

Locate the three snap hooks and use your fingers to flip
over and place the PBA Key Flex Flip Complete.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

81(87)

Working Instruction, Mechanical

4.10 Cover Flip Front

Use your fingers to position the Cover Flip Front in the rear
end.

Use your fingers to snap on the Cover Flip Front.

Use your fingers to slide and position the Cover Flip Front
to make the two Screw 2.3x1.4 holes visible through the two
holes in the Cover Base Rear Assembly.

Use a Screwdriver with JCIS Bit (torque 11Ncm) to insert
and tighten the two Screw 2.3x1.4.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

82(87)

Working Instruction, Mechanical

4.11 Cap Plastic RF Numeric Keyboard & Cap Numeric
Keyboard

Use a pair of ESD tweezers to place the Cap Plastic RF
Keyboard Numeric.

Use a pair of ESD tweezers to place the Cap Numeric
Keyboard.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

83(87)

Working Instruction, Mechanical

4.12 Keyboard

Use a Flex Film Assembly Tool to position the Keyboard.

Place the phone on the Keyboard Pressure Tool as the
picture shows. Set the Pressure Tool to 50 N.
FIND THE USER GUIDE FOR THE PRESSURE TOOL IN
CSPN/REPAIR INSTRUCTIONS/MECHANICAL/TOOL
CATALOGUE (SPACE ID 1003-9107)
OPEN ZIP FILE/ PDF DOCUMENT SPACE ID 1219-2553

Use the Pressure Tool to attach the Keyboard

Use the Pressure Tool to press the Keyboard for 10
seconds.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

84(87)

Working Instruction, Mechanical

4.13 Foil Flip Inner

Use a Screwdriver with JCIS Bit (torque 11Ncm) to insert
and tighten the two Screws 4.0x1.4.

Use a pair of ESD Tweezers to position and attach the Foil
Flip Inner.

4.14 Battery Cover & Battery

Use your fingers to attach the Battery.

Use your fingers to attach the Battery Cover.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

85(87)

Working Instruction, Mechanical

5 Country of Origin Barcodes for Brazil/VIVO
Labels
Below is a link to a list of countries of origin. If you are printing a Brazil or VIVO label, scan the
barcode corresponding to the correct country of origin for the "Fabricado" field.

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

86(87)

Working Instruction, Mechanical

6 Revision history
Rev.
1
2
3

Date
2008-10-24
2008-11-04
2008-11-20

Changes / Comments
First release
Chapter 1.1, 2.2, 2.5, 2.10, 4.4, 4.6, 4.8 changed
Spacer for Rigid Flex Fixation added, and revised text

1218-1731 Rev 3
Company Internal (C) Sony Ericsson Mobile Communications AB

87(87)


Download file - link to post