ADVERTISEMENT

MC-049A Adjustment Spec_041209.doc

LG RZ-21FB35RX - Pilnie potrzebne wartości trybu serwisowego chassis MC-049B

Może Ci pomoże.


Download file - link to post

MC-049A Adjustment Spec

NTV Development Group

1.Scope

These adjustment instructions are applied to MC-049A chassis.

2. Notes

2.1. Because this is a cold chassis, it is not necessary to use an
isolation transformer.

But, operate it using a transformer between the power supply line
and chassis

input to prevent electric shock and to protect the test
instrument.

2.2. All adjustments must be done in correct sequence.

However, for the better productivity, it can be changed in
pre-permitted range.

2.3. Environment conditions : If not specified, it must be done in
following conditions.

1) temperature : 25? ± 5?

2) Humidity : 65% ± 10%



2.4. Power supply of a SET which is adjusted is (100?240V)±10% AC,
50?60Hz



2.5. If not specified, the receiver must be operated for more than 20
minutes prior to

the adjustment.

2.6. Signal : Receive the standard color signal. (65dB±1dB uV)

LG standard signal means the digital pattern 13CH(480NC)

2.7. If not specified, APC ON is APC CLEAR.

3. Adjustment contents

3.1. Focus voltage adjustment

3.2. Purity & Convergence adjustment

3.3. Screen Voltage adjustment

3.4. White Balance adjustment

3.5. Deflection adjustment

3.6. Deflection setting Initial data

3.7. SERVICE adjustment data table

3.8. OPTION data setting

4. IN-STOP MODE setting

3.1. Focus voltage adjustment

3.1.1. Receive the LG standard pattern(digital pattern, 480NC, 13CH).

3.1.2. Set the picture condition on `APC CLEAR' mode.

3.1.3. Adjust the Focus volume of FBT for the best focus of horizontal
line A,

vertical line B.







3.2. Purity & Convergence adjustment

3.2.1. Purity adjustment

(1) Preparation

? Receive the RED Raster Pattern for purity adjustment.(11CH)

? Demagnetize the CPT and Cabinet with a degaussing coil.

(2) Adjustment

? Pre-adjust the static convergence(STC) with 4 and 6-pole magnet.

? Push the DY(deflection Yoke) all the way to the CPT pannel.

? Turn the purity magnet(2-pole magnet) so that the `green'
portion of left side

and the `blue' portion of right side have same portion.

? Pull the DY slowly and fix it when the whole screen become red.


3.2.2. Convergence adjustment

(1) Preparation

? Receive the Cross Hatch pattern for convergence
adjustment.(09CH)

? Let the contrast at the adequate luminance level.

(2) Adjustment

? Converge the RED vertical line and BLUE vertical line in the
same line by

changing the angle between the 2 tabs of the 4 pole magnet.

? Converge the RED horizontal line and BLUE horizontal line in the
same line by

turning the 2 tabs of the 4 pole magnet. This time, do not
change the angle

between the 2 tabs.

? Converge the R, G, B vertical line in the same line by changing
the angle between

the 2 tabs of the 6 pole magnet.

? Converge the R, G, B horizontal line in the same line by turning
the 2 tabs of

the 6 pole magnet. This time, do not change the angle between
the 2 tabs.

3.3. Screen voltage adjustment

3.3.1. Receive the NTSC or PAL-M/N signal into RF mode ( regardless of
channel.)

3.3.2. If you press the ADJ button in LINE SVC mode (IN-START button),
the LINE SVC

mode changes to screen adjustment mode.

3.3.3. Turn the Screen volume of FBT until the horizontal line is no
longer seen

and then stop.

3.3.4. Press the TV/AV button to exit SVC mode.

3.4. White Balance Adjustment

Prior to this adjustment, screen voltage adjustment must be finished.

3.4.1. Necessary Instrument

(1). White Pattern Generator (Can generate Low/High Light pattern)

(2). White Balance meter( CRT color Analyzer,CA-100)

(3). Factory Remote control

3.4.2. Preliminary steps

(1). Tune the TV set to receive an 100% white pattern.

(2). Perform screen adjustment first.

3.4.3. Adjustment

(1). Enter into adjustment mode by ``INSTART'' key and select
SERVICE1 mode.

(2). Adjust the item with CH+/- Key.

(3). Adjust the data with VOL+/- Key.

(4). Adjustment Procedure

Adjust``CONTRAST'' and ``BRIGHT'' so that the bright level is 35Ft-L.

Select B DRIVE to adjust Y coordinate in High Light and select R DRIVE

to adjust X coordinate so that the color coordinates in High Light match
the values

In Table below.

Adjust `CONTRAST'' and ``BRIGHT'' so that the bright level is 4.5Ft-L.

Select B CUT to adjust Y coordinate in Low Light and select R CUT

to adjust X coordinate so that the color coordinate in Low light match
the values in

Table below.

Repeat ? ~ ? until the color coordinates in High and Low color
satisfies the Table.

Check the adjusted color coordinates with the white balance meter

Store the W/B adjustment data in EEPROM by using ENTER button before
EXIT.

[ White Balance Color coordinates ]

EU N-EU KOREA PHILIPPINES

X 288 268 267 266

Y 295 273 276 282

Temperature 9000 13000 13000 13000



[ WHITE BALANCE Initial Data]

Description Item Range Initial data refer

LOW LIGHT R CUT 0 ~ 511 80



G CUT 0 ~ 511 80 FIX

B CUT 0 ~ 511 80

HIGH LIGHT R DRIVE 0 ~ 511 430



G DRIVE 0 ~ 511 430 FIX

B DRIVE 0 ~ 511 430



* Note : When adjusting white balance automatically, connect the
adjustment JIG in SVC mode.

(When pressing IN-START, MUTE button on remote control for
adjustment orderly,

it changes to SVC mode and screen displays ``CPU OFF''.)



3.5. Deflection adjustment



3.5.1. Preparation

(1) At adjustment mode (IN-START button on remote control of
adjustment), changed to

SERVICE 2 mode to adjust the deflection.

(2) Press Channel +/- button for desirous function adjustment.

(3) Press Volume +/- button to adjust the data.

(4) Tune the TV set to receive a Digital pattern.

3.5.2. Deflection setting data adjustment (Digital pattern : 480NC,
13CH)

* Note : First, adjust deflection at 50Hz of PAL signal.

Then, adjust deflection at 60Hz of NTSC signal.

Store the deflection adjustment data in EEPROM by using
ENTER button.

Press Exit button to exit SVC mode.

(1) VL (Vertical Linearity)

Adjust so that the boundary line between upper and lower half
is in accord with geometric

horizontal center of the CPT.

(2) VA (Vertical Amplitude)

Adjust so that the circle of a digital circle pattern may be
located within the effective

screen of the CPT.

(3) SC (Vertical S-Correction)

Adjust so that all distance between each horizontal lines are
to be the same.

* Recommend initial setting data.

(4) VS (Vertical Shift)

Adjust so that the horizontal center line of a digital circle
pattern is in accord with

geometric horizontal center of the CPT.

(5) HS (Horizontal Shift)

Adjust so that the vertical center line of a digital circle
pattern is in accord with

geometric vertical center of the CPT.

(6) EW (Horizontal Width)

Adjust to that a digital circle pattern looks like exact
circle.





[Fig 3] PAL Digital Pattern (EU05CH) [Fig 4] NTSC
Digital Pattern (US13CH)

(7) ET (East-west Trapezium)

Adjust to make the length of top horizontal line same with it
of the bottom horizontal line.

(8) EP (East-west Parabolar)

Adjust so that middle portion of the outermost left and right
vertical line looks like parallel

with vertical lines of the CPT.

(9) CRNU (Upper Coner )

Adjust until symmetrize upper coner of the screen.

(10) CRNL (Lower Coner)

Adjust until symmetrize upper coner of the screen.

(11) BOW

Adjust the left and right crooked line on upper and lower side.


(12) ANGLE

Adjust the vertical slope.

(13) CRNU6

More deatail adjust until symmetrize upper coner of the screen.

(14) CRNL6

More deatail adjust until symmetrize Lower coner of the screen.

(13) PIP H (PIP H position)

Adjust until the distance between PIP and main picture becomes
about 1?2mm.

[Fig 5] PIP H Position Adjust Picture

( Only PIP Function model)

3.6 Deflection setting Initial data

Deflection setting Initial data(SERVICE 2)

1). LG 25''/29'' FLAT & FST CPT Model

ITEM Description Range N 50Hz(PAL) Adjust or

Recommend



29'' FLAT 25'' FLAT 29''

FST 25''

FST

VA Vert. Position -512~511 48 54 -70 25 Adjust

VL Vert. Linearity -512~511 -12 -44 0 -12 Recommend

SC S-Correction -512~511 140 140 140 140 Recommend

VS Vert. Amplitude -512~511 12 6 5 5 Adjust

HS Hor. Position 32~2047 147 157 162 160 Adjust

EW Hor. Width -256~255 -73 -69 -37 -44 Adjust

ET Trapezoidal -512~511 -13 -7 -12 -3 Adjust

EP Pin Cushion -512~511 -73 -88 -100 -118 Adjust

CRNU Upper Corner -512~511 8 8 35 15 Adjust

CRNL Lower Corner -512~511 12 12 35 15 Adjust

BOW Bow -512~511 0 0 0 6 Recommend

ANGLE Angle -512~511 0 0 0 0 Recommend

CRNU6 Upper Corner(6TH) -512~511 0 0 0 0 Recommend

CRNU6 Lower Corner(6TH) -512~511 0 0 0 0 Recommend

OSD P OSD Position -64 ~ 63 0 0 0 0 Recommend

PIP H PIP H Position 0 ~40 0 0 0 0 PIP model only

Adjust : It is possible to adjust data.

Recommend : It is recommended, if necessary it is possible to adjust.

FIX : Don't change data.

2). LG 28'' WIDE FLAT & 28'' FST(PHILIPS) CPT Model

ITEM Description Range N 50Hz(PAL) Adjust or

Recommend



LG 28''

WIDE FLAT PHILIPS 28''

FST

VA Vert. Position -512~511 -255 -15 Adjust

VL Vert. Linearity -512~511 -30 -40 Recommend

SC S-Correction -512~511 140 200 Recommend

VS Vert. Amplitude -512~511 9 9 Adjust

HS Hor. Position 32~2047 162 165 Adjust

EW Hor. Width -256~255 -70 -40 Adjust

ET Trapezoidal -512~511 -0 2 Adjust

EP Pin Cushion -512~511 -70 -152 Adjust

CRNU Upper Corner -512~511 15 37 Adjust

CRNL Lower Corner -512~511 15 6 Adjust

BOW Bow -512~511 0 3 Recommend

ANGLE Angle -512~511 0 2 Recommend

CRNU6 Upper Corner(6TH) -512~511 0 1 Recommend

CRNU6 Lower Corner(6TH) -512~511 0 30 Recommend

OSD P OSD Position -64 ~ 63 0 0 Recommend

PIP H PIP H Position 0 ~40 0 0 PIP model only



3). SDI 29'' FLAT

ITEM Description Range N 50Hz(PAL) Adjust or

Recommend



SDI 29'' FLAT

VA Vert. Position -512~511 291 Adjust

VL Vert. Linearity -512~511 -12 Recommend

SC S-Correction -512~511 140 Recommend

VS Vert. Amplitude -512~511 16 Adjust

HS Hor. Position 32~2047 160 Adjust

EW Hor. Width -256~255 -27 Adjust

ET Trapezoidal -512~511 -2 Adjust

EP Pin Cushion -512~511 -100 Adjust

CRNU Upper Corner -512~511 10 Adjust

CRNL Lower Corner -512~511 2 Adjust

BOW Bow -512~511 1 Recommend

ANGLE Angle -512~511 1 Recommend

CRNU6 Upper Corner(6TH) -512~511 24 Recommend

CRNU6 Lower Corner(6TH) -512~511 14 Recommend

OSD P OSD Position -64 ~ 63 0 Recommend

PIP H PIP H Position 0 ~40 0 PIP model only



3.7 SVC Adjustment data table

1)SERVICE1

ITEM Description LG

25''/29''

FLAT LG

25''/29''

FST PHILIPS

28''

FST LG

28''

FLAT SDI

29''

FLAT

S-BRI Sub Bright( Luma Offset) 0 0 0 0 0

YCDEL Luminance Delay -3 -3 -3 -3 -3

EXCON External Contrast -1 -1 -1 -1 -1



2)SERVICE2

ITEM Description LG

25''/29''

FLAT LG

25''/29''

FST PHILIPS

28''

FST LG

28''

FLAT SDI

29''

FLAT

HBSO Horizontal Blanking Stop 185 185 200 200 222

HBST Horizontal Blanking Start 1250 1250 1260 1260 1265

EHTTH EHT Compen. Threshold 150 150 150 150 150

EHT S EHT Static Time constant 100 100 100 100 100

EHTV1 Static V Comp.(1ST Gain) -17 -17 -17 -17 -17

EHTV2 Static V Comp.(2nd Gain) -70 -70 -70 -70 -70

EHTH1 Dynamic H Comp.(1ST Gain) -3 -3 -3 -3 -3

EHTH2 Dynamic H Comp.(2nd Gain) -10 -10 -10 -10 -10

EHT F EHT Dynamic Time constant 1 1 1 1 1



3)SERVICE3

ITEM Description LG

29''

FLAT LG

25''

FLAT LG

29''

FST LG

25''

FST LG

28''

W/FLAT PH

28''

FST SDI

29''

FLAT

BCLTH BCL Threshold Current 435 330 350 350 350 270 435

BCLTC BCL Time Constant 507 507 507 507 507 507 507

BCLGA BCL Loop Gain 480 210 300 300 300 380 480

BCLC BCL Minimum Contrast 200 230 200 230 200 230 200

SVM D SVM Delay 4 4 4 4 5 4 4

SVM G SVM Gain 20 20 20 20 10 20 5

VBSO Vertical Blanking Stop 22 22 22 23 20 22 20

VBST Vertical Blanking Start 312 312 312 312 312 312 312

PLLTC Time Constant HPLL 1 1 1 1 1 1 1

NMLIM Noise Measurement Line 30 30 30 30 30 30 30



4)SERVICE4 (All models are equally applied)

ITEMS Description ALL MODEL

FP FM PRE-SCALER 28

NP NICAM PRE-SCALER 60

SP SCART PRE-SCALER 24

S1VOL SCART1 PRE-SCALER 117

S2VOL SCART2 PRE-SCALER 117

AGC-L AUTO GAIN CONT. LIMIT 670

M-STR Bass Effect Strength 45

M-HMC Bass Harmon Cont 25

M-HP Bass HP Corner Freq 9

M-LP Bass LP Corner Freq 11

M-LIM Bass Ampl-Limit 252

TOPST Tuner Take-Over-point 4

VID-P Freq. Resp Video peak Filter 1

THRSL H Slicing Level Threshold 1

SLTHD Slicing Level Threshold Offset H 0

THDVP Vertical Slicing Level Threshold Polarity 1

THDV Slicing Level Threshold V 6

LNA-L LNA Level 4

CRAMP Carrier Recovery Amplitude Threshold 0



3.8. OPTION data Setting (OPTION-1,2,3,4,5)

3.8.1. Preparation for Adjustment

(1) This decides function in accordance with model.

Press the SVC TX adjustment button (IN-START button) at SVC
mode, then adjust

the option at OPTION 1, 2, 3, 4,5 mode.

(2) Mark the option adjustment data like (112,68,164,32,8) in BOM.

? Mark of BOM ( Example)

LEVEL PART NO. SPECIFICATION DESCRIPTION

1. 3141VMN382A MAIN CHASSIS ASSY [112,68,164,32,8]



1). OPTION1 Function

OPTION CODE FUNCTION REMARK

INCH 0

1

2

3

4

5

6

7 21A

21B

21C

29F/25F

28WF/32WF

28N

34F

29N/25N



SYS 0

1

2

3 BG/I/DK

BG/I/DK/L

BG/I/DK/M

BG/L



SOUND 0

1

2

3 RF STEREO

AV STEREO

MONO

MONO DUAL

CH + AU 0

1 WITHOUT D/K CHINA or BB SYSTEM

WITH D/K CHINA or BB SYSTEM

CHINA, Austrailia



2). OPTION2 Function

OPTION CODE FUNCTION REMARK

AV2 0

1 WITHOUT AV2 JACK (BACK)

WITH AV2 JACK (BACK)

DVD 0

1 COMPONENT(480i) ?

COMPONENT(480i) ?

1SCRT 0

1 PHONE JACK ONLY

SCART + PHONE JACK

GAME 0

1 WITHOUT GAME

WITH GAME ( PACK )



EYE 0

1 WITHOUT EYE

WITH EYE

TX 0

1 LARGE

SMALL For MC-049A

For MC-049B

KEY 0

1 6, 8 KEY

4KEY

DEGAU 0

1 WITHOUT DEGAUSSING

WITH DEGAUSSING



3). OPTION3 Function

OPTION CODE FUNCTION REMARK

TEXT 0

1 200PR ( WITHOUT TEXT )

100PR ( WITH TEXT )

TOP 0

1 FLOP TXT

TOP TXT

ACMS 0

1 WITHOUT ACMS FUNCTION

WITH ACMS FUNCTION

I II SV 0

1 NO SAVE DUAL SOUND CONDITION

SAVE DUAL SOUND CONDITION EU

NON EU

VOL 0

1 NORMAL VOLUME CURVE??

RUSHED VOLUME CURVE??



TSEAR 0

1 WITHOUT TURBO SEARCH

WITH TURBO SEARCH

T P-S 0

1 WITHOUT TURBO PICTURE/ SOUND

WITH TURBO PICTURE/ SOUND

HDEV 0

1 WITH OUT HIGH DEVIATION OPTION

WITH HIGH DEVIATION OPTION ????

Indonesia,China, Indo



4). OPTION4 Function

OPTION CODE FUNCTION REMARK

OSD L 0

1

2

3

4

5

6

7

8

9

10 ENG ONLY

EU-5EA

EU ETC

GREECE

EU-ALL

FARSI

ARAB URDU

E+HINDI

E+I+M+V

E+THAI

E+CHINA

TXT L 0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17 ?,?,???,??,?,???,???

???, ?,???,??,?,?????, ???, ????

?, ?, ???, ???, ?, ???, ???

?, ??,???,????, ?, ???, ???, ????

???, ???, ?????, ???

???, ???, ???, ??, ?????, ???

?, ???, ?????, ??, ? ?????, ???

?, ?, ???, ???, ?, ???, ???, ????

?, ???, ?, ????

?, ?, ???, ???, ?, ???, ???, ????

?, ?, ???, ???

?, ?, ???, ???

???, ???

?, ?, ???, ???

?, ?, ???, ???

?, ???,??? WEST EU

EAST EU1

TURKEY EU

EAST EU2

CYRILLIC1

CYRILLIC2

CYRILLIC3

TURK GRE1

TURK GRE2

TURK GRE3

ARAB FRA

ARAB ENG

ARAB HEB1

ARAB HEB2

FARS ENG

FARS FRA

FARS ALL

AUTO

HOTEL 0

1 WITHOUT HOTEL OPT ON

WITH HOTEL OPT ON



MAX V 0 ~

100

At time HOTEL OPT. 1 is set.





5). OPTION5 Function

OPTION CODE FUNCTION REMARK

AV3 0

1 WITHOUT AV3

WITH AV3

SAV 0

1 WITHOUT S-VIDEO

WITH S-VIDEO

WOOF 0

1 WITHOUT WOOFER SPK

WITH WOOFER SPK

TILT 0

1 WITHOUT TILT

WITH TILT



BOOST 0

1 TUNER WITHOUT BOOSTER

TUNER WITH BOOSTER

2SCRT 0

1 MODEL WITHOUT 2 SCART JACK MODEL

MODEL WITH 2 SCART JACK



CHINA 0

1 Not China Model

China Model

A2 ST 0

1 Without A2 ST

With A2 ST

4.IN STOP Setting

It must be pushed IN STOP button before shipment.

4.1.Shipping Condition


Number Items Condition Remarks

1 ? ? OFF

2 Input TV

3 MEMORY CHANNEL CH. MEMORY ??????

4 SOUND 30 STEPS

5 MUTE OFF

6 TURBO SOUND OFF

7 PSM DYNAMIC

8 SSM FLAT

9 BOOSTER ON

10 CHILD LOCK OFF

11 AUTO SLEEP OFF

12 AVL OFF

13 BALANCE 0

14 BLUE BACK OFF

15 EYE OFF

16 TILT 0

17 DEGAUSS OFF



*** PSM MODE

PSM Dynamic Standard Mild Game

CONTRAST 100 90 70 60

BRIGHT 60 60 55 50

COLOR 60 55 50 40

SHARPNESS 60 50 50 40



PAGE

PAGE

PAGE 13

(A)

[Fig 1] PAL Digital Pattern (EU05CH)

[Fig 2] NTSC Digital Pattern (US13CH)

(B)

PAGE 13 /29

?? :2003/1

?? :

LG

? ??? ?? ??? LG

(51)

-

LG ??